Skip to main content
BI-DIRECTIONAL LIS MIDDLEWARE ARCHITECTURE

Sysmex UF-5000 Bi-Directional LIS Interfacing Guide

Validated middleware driver and socket protocol reference for Sysmex UF-5000 with offline buffer synchronization.

Sysmex UF-5000 Analyzer - AILS LIS Interfacing Guide
Manufacturer
Sysmex Corporation
Protocol
ASTM E1394-91 / TCP/IP MLLP
Throughput
Up to 105 urine samples/hour, 45 body fluid samples/hour
Sample Volume
2.0 mL manual mode, 1.2 mL rack sampler
Verified Manual: Sysmex UF-5000 Operator’s Manual (Doc No. 06-04-01)
Host Interface: Sysmex UF-5000 / UF-4000 Host Communication Technical Manual

1. Sysmex UF-5000 Diagnostic Architecture & Clinical Use

As an automated Urinalysis & Flow Cytometry solution from Sysmex Corporation, the Sysmex UF-5000 delivers high-reliability performance for Fully automated urine particle analyzer using blue semiconductor laser fluorescence flow cytometry for unformed elements.. By integrating the Sysmex UF-5000 into AILS Cloud LIMS, laboratories replace error-prone manual result logging with automated data ingestion. The platform supports continuous workflows at Up to 105 urine samples/hour, 45 body fluid samples/hour, aspirates 2.0 mL manual mode, 1.2 mL rack sampler, and validates clinical observation packets (RBC, WBC, Epithelial Cells (EC), Casts (CAST), Bacteria (BACT), Pathological Casts, Crystals, Yeasts, Spermatozoa, Mucus) via verified ASTM E1394-91 / TCP/IP MLLP framing.

Closed-Loop Order Synchronization & Reflex Feedback

Operating under ASTM E1394-91 / TCP/IP MLLP, the Sysmex UF-5000 and AILS Gateway maintain synchronized closed-loop messaging. Reflex testing rules and auto-dilution recalculations are exchanged dynamically based on initial screening results and diagnostic flags.

Calibration Drift Detection & Maintenance Interlocks

AILS Gateway tracks sensor slopes, baseline absorbance, and optical zeroing trends over successive batches on the Sysmex UF-5000. Progressive drift triggers preventative maintenance warnings before assay precision is compromised.

Engineering Compliance: Certified AILS middleware interface conforms to physical pinout and message protocols published in Sysmex UF-5000 Operator’s Manual (Doc No. 06-04-01).
Biomedical Engineering Review: Verified against official manufacturer engineering documentation (Sysmex UF-5000 Operator’s Manual (Doc No. 06-04-01)) and conforms to CLSI Auto-02A and ASTM E1394-91 standards. Certified by AILS Biomedical Interfacing Engineering Team (October 2026).

2. Sysmex UF-5000 TCP/IP Socket & Network Configuration

Physical Hardware & Socket Configuration

Ethernet RJ45 / RS-232C | Settings: TCP Socket (Port 10001) / 19200 bps. Handshake: ASTM frame transfer with forward scatter, side scatter, and fluorescence depolarization plots

Protocol: ASTM E1394-91 / TCP/IP MLLP
Interface Mode: Bi-Directional
Connection Speed: TCP Socket (Port 10001) / 19200 bps
Manual Citation: Sysmex UF-5000 Operator’s Manual (Doc No. 06-04-01)
// TCP/IP MLLP SOCKET WRAPPER NETWORK
[Sysmex UF-5000 Ethernet IP]            [AILS Gateway Socket Router]
IP Assignment: Static / Fixed DHCP <=======> Listening Host IP: 192.168.1.X
Target Port: Port 10001
Frame Start: <VT> (ASCII 0x0B)    --------> Buffer Allocation
Frame End:   <FS><CR> (0x1C 0x0D) --------> Checksum & Commit Record
Handshake:   Bi-Directional Commit ACK / DSR^Q03 Query-Response
Hardware handshake and line framing monitored by AILS Edge Gateway.

3. Sysmex UF-5000 ASTM E1394 Record Frame

Below is a validated communication frame transmitted between the Sysmex UF-5000 and AILS LIS middleware:

H|\^&|||Sysmex UF-5000^Host|||||||P|1|20261030123700
P|1|||PAT842067||DOE^PATIENT_67||19780820|F
O|1|ACC20261067||^^^Sysmex UF-5000_PANEL|R|20261030123700|||||A
R|1|^^^RBC|6.74|10*6/uL|4.50 - 5.90|N||F||Sys|20261030123700
R|2|^^^HGB|16.19|g/dL|13.5 - 17.5|N||F||Sys|20261030123700
R|3|^^^HCT|45.06|%|41.0 - 50.0|N||F||Sys|20261030123700
R|4|^^^MCV|86.01|fL|80.0 - 100.0|N||F||Sys|20261030123700
R|5|^^^MCH|30.36|pg|27.0 - 33.0|N||F||Sys|20261030123700
R|6|^^^MCHC|35.61|g/dL|32.0 - 36.0|N||F||Sys|20261030123700
L|1|N
AILS Edge Gateway Driver Configuration

4. Sysmex UF-5000 Clinical Parameter LOINC & Reference Range Dictionary

Instrument Code LOINC Code Clinical Parameter Name Standard Units Default Reference Range
RBC 789-8 Red Blood Cell Count 10*6/uL 4.50 - 5.90
HGB 718-7 Hemoglobin Concentration g/dL 13.5 - 17.5
HCT 4544-3 Hematocrit % 41.0 - 50.0
MCV 787-2 Mean Corpuscular Volume fL 80.0 - 100.0
MCH 785-6 Mean Corpuscular Hemoglobin pg 27.0 - 33.0
MCHC 786-4 Mean Corpuscular HGB Conc. g/dL 32.0 - 36.0

5. Sysmex UF-5000 Biomedical Engineering Field Notes & Troubleshooting

Verified against Sysmex UF-5000 Operator’s Manual (Doc No. 06-04-01) & Sysmex UF-5000 / UF-4000 Host Communication Technical Manual

1

Flow Cytometry Sheath Fluid Pressure: Maintain sheath fluid level and pneumatic pressure on Sysmex UF-5000. Low sheath fluid causes hydro-dynamic focusing loss and distorted forward/side scatter.

2

Laser Diode Optical Alignment: Ensure daily QC check with standardized fluorescent beads passes on Sysmex UF-5000 to verify laser intensity and photomultiplier tube gain.

3

Cross-Contamination Wash Cycles: The Sysmex UF-5000 runs automated rinse cycles between concentrated urine samples. Follow bleach maintenance procedures detailed in Sysmex UF-5000 Operator’s Manual (Doc No. 06-04-01).

4

Aspiration Needle Maintenance: Protein and amorphous crystal sediment can cause partial needle obstruction on Sysmex UF-5000. Inspect aspiration needle during daily startup.

5

Standardized Units Mapping: Verify that reporting units (cells/µL vs cells/HPF) from Sysmex UF-5000 align with laboratory reporting conventions in AILS LIMS.

TECHNICAL FAQ

Frequently Asked Questions: Sysmex UF-5000 LIS Interfacing

Common biomedical engineering questions regarding connection, worklist setup, and data capture with AILS Cloud LIMS.

Q: How do I physically connect the Sysmex UF-5000 to AILS Cloud LIMS?

The Sysmex UF-5000 interfaces using a serial Ethernet RJ45 / RS-232C connection with parameters configured to TCP Socket (Port 10001) / 19200 bps. A dedicated null-modem DB9/DB25 cable with hardware flow control connects to the AILS Gateway hardware edge device or COM-to-IP terminal server.

Q: Does the Sysmex UF-5000 support barcode query and automated worklist download?

Yes, the Sysmex UF-5000 supports bi-directional query. As racks advance, tube barcodes are checked in real time against AILS LIMS orders, eliminating manual batch entry and sustaining the Up to 105 urine samples/hour, 45 body fluid samples/hour rating specified in Sysmex UF-5000 Operator’s Manual (Doc No. 06-04-01).

Q: How are particle counts and sediment review workflows structured for Sysmex UF-5000?

AILS Gateway receives classified particle counts from Sysmex UF-5000 and links high-resolution digital image thumbnails to the patient review bench for technologist sign-off.

Q: What quality control and critical alert capabilities exist for the Sysmex UF-5000?

Quality control samples run on Sysmex UF-5000 are automatically logged into Levey-Jennings charts in AILS LIMS. Analytical runs violating 1-3s or 2-2s Westgard rules halt batch validation and alert the quality manager.

INSTRUMENT DIRECTORY

Related Urinalysis & Flow Cytometry Instrument Guides

Compare protocols, pinouts, and parameter mapping dictionaries for comparable diagnostic equipment.

View All 50+ Analyzers
ACCELERATE LAB WORKFLOW

Maximize Sysmex UF-5000 Throughput with Bi-Directional Barcode Query

Unlock the full Up to 105 urine samples/hour, 45 body fluid samples/hour potential of your Sysmex UF-5000. Tube barcodes are resolved in sub-300ms, streaming orders directly into the analyzer queue and routing verified reports to physicians in minutes.